2014 The Italian Sea Group Admiral Sail - Silent 76, Carrara Italy

Read article : 2014 The Italian Sea Group Admiral Sail - Silent 76, Carrara Italy

Features:

1. Construction

Hull Construction:

The hull is moulded in GRP from female moulds; it uses a high properties gelcoat and the internal side of the hull is vacuum infused with isoftalic polyester resin while the skincoat features a further application of vi-nylester resin in order to avoid and limit osmosis. Additional reinforce-ments are included to the keel area, the keel longitudinal, mast bulkhead, structural P-brackets, engine room basement, forestay and hull stringers. Limber holes which penetrate structural areas and/or tubes are installed at appropriate points on stringers, bulkhead – landings and floors.

Hull Finishes:

Grey metal hull and with light grey superstructure; red waterline and black antifouling;

Deck Construction:

Moulded in GRP with a PVC foam cored structure for strength and insula-tion. In load bearing areas the core is replaced with plywood for additional strength, and all load bearing fittings have backing plates.

The hull to deck connection is achieved by bonding the deck onto the return flange of the hull and using the glue approved by Class rules in or-der to create a structural junction.

Deck Finishes:

The weather deck, cockpit seats, sole areas and part of the coachroof area are finished with teak planking (10mm). This is laid using epoxy ad-hesive, with no visible fastenings.

The areas either side of the main companionway are finished with teak planking, with open stowage areas and stainless steel rails.

All lockers drain outside and their hinges and catches are recessed or hid-den into Teak planking, as appropriate.

Keel System:

The keel is a high performance bulb design.

The ballast keel is made of lead casting bolted to the GRP hull with stain-less steel bolts. Ballast weight is approximately 14,800 kgs. .

The keel is designed to combine moderate draft with good sailing perfor-mance due to its efficient shape and side winglets. The centre of gravity is very low due to the fact that the centerboard is made of cast iron while the actual keel is made of lead.

Mast and Boom:

Max Spar conventional alloy mast (made of two parts) with Ronstan track for in-boom furling mainsail with top tapered (last 3 meters). Triple spread-er rig with tapered aerofoil spreaders (21° angle).

Custom carbon boom – deep and trapezoidal section incorporating Bamar furling system and electric motor for in-boom furling mainsail.

Mast & Boom and Mast & Vang connections are custom made in alumi-num and feature a special, custom made concealing cover, made of car-bon, which gives a unique design. Also the vang itself feature a custom made concealing cover, made of two carbon conical blocks.

Deck Fittings:

Stainless steel opening pulpit;

Port and starboard navigational lights;

Stainless steel pushpit with gate for boarding;

Custom stainless steel and teak made engine bracket;

650mm stainless steel custom stanchions and bases with double stainless steel rod guardrails;

Pair of gateway stanchions for side access;

Stainless steel telescopic and retractile steamhead fitting with single roller designed to stow a 63kg Delta anchor. The chain flows into the steamhead arm itself, without the need of having an external chainplate;

Pair of custom stainless steel, leather upholstered backrest seats fitted at the helm positions;
6 x pairs of 400mm stainless steel “pop-up” mooring cleats with chafe strips to deck edges;
4 x pairs of aft “pop-up” fairleads and cleats in proximity of the transom bulwark;
Deck fillers – 2 x fuel, 2 x water and 1 x waste;
1000W Sanguinetti Chiavari retractile capstan for mooring lines at bow;

Cockpit:

The cockpit is split into separate guest and steering/crew areas, although they are both on the same level.
The main companionway features a double large horizontal sliding hatchway with stainless steel frames and grab rail. The sliding mechanism is manually powered.
The guest cockpit is over 3m long and self-draining as it’s on the same level of the main deck. There are also cockpit drains which ease the water to drain away while at sea and going upwind. There is a clear walkway giving excellent access from the companionway to the helm positions and side decks, all on the same level.
The cockpit features two teak-topped opening, sliding and telescopic tables.
The tables are permanently installed and have seats on three sides due to the cockpit design. The table is provided with a cover. Under one of the cockpit seats a top opening fridge finds place.
Three pairs of flush mounted waterproof loud speakers are mounted in the guest cockpit with their own cockpit mounted remote control unit for the dedicated ‘cockpit’ CD/Tuner head unit (head unit installed below decks).
Two of those speakers are used by the vhf system, as external loud speakers.
The helm position has twin custom GRP and aluminium steering pedestals
incorporating all the standard controls and instruments with plenty of room for additional equipment, if required. Each pedestal has a flush-mounted compass with internal lighting. There is a double lever engine control fitted at the starboard pedestal. The wheels are fitted in a reverse position, giving easy and safe access to the instruments mounted on both pedestals.
At the helm position an aluminium roll-bar finds place. This is the base where the two fixed points for the mainsheet system are fitted.
Aft the helm positions is a clear flat deck area, which can be filled with cushions, creating a sunbathing area. This area also includes two big lockers with flush-to-deck lids, teak covered; they are designed to host two liferafts or alternatively one can be dedicated to a liferaft and the other one to store lines. A custom flush hatch is fitted with twin gas struts, drain channels, rubber seal and against the wind closing to give access to the large dinghy garage.

Garage & Bathing Platform:

The yacht is built with a flap-down full beam transom, raised and lowered hydraulically, which also gives the main access to the toys garage. The garage can host a good number of toys and actually it fitted to host 3 seabobs.
The bathing platform created by the transom once it’s open it is provided with a demountable stainless steel bathing ladder and it’s covered by teak planking.
A removable ladder also connects the main deck to the transom when open. Alternatively also the gangway can be used for this purpose.
There is a hot and cold freshwater deck shower located in the dinghy garage which can be used on the bathing platform thanks to a flexible hose.
The garage door is also provided with an emergency system for opening the garage, which is placed close to the waterline, protected by a stainless steel screwed in cap and which can be operated by a person in the water.

Hard Top:

The yacht features a custom cockpit hard top, which gives a very good protection to the all cockpit and helm positions. This feature is unique on yachts of this size and contributes to the overall design of the yacht.

The hard has an aluminium structure, attached to the aluminium roll-bar which is placed aft. The practical functions of this will be both sprayhood and bimini.
The hard top has a glass cover and an opening area which is covered with acrylic material (Sunbrella), with battens.
The hard top also features side glasses which deliver complete protection to the forward end of the cockpit seats.

Anchoring:

A Quick 3000w electric anchor windlass is installed below deck and within the anchor chain locker. The windlass, which is two-way and operated by adjacent foot switch controls is well over specified for the size of the vessel.
The 63kg (approximately) Delta anchor stows into the retractable stemhead fitting.
120 metres of 12mm calibrated, galvanized chain is fitted to match the
windlass. The chain is fastened at its 'bitter end' to a through-bolted stainless
steel attachment with substantial lanyard.

Haatches, Windows and Portholes:

1 x Lewmar over forward crew cabin;
1 x Lewmar over forward VIP cabin;
1 x Lewmar over main saloon;
1 x Lewmar over garage (with teak planked lid);
Custom main companionway with double sliding and balanced hatch system,
stainless frames and grab rails (by SeaSmart);
1 x custom GRP hatch to cover anchor steamhead locker;
Custom direct bonded, curved and flat, non-opening frameless deck saloon
windows, smoked glass made (by Viraver);
8 x custom direct bonded non-opening frameless hull windows, smoked glass made (by Viraver);

Whinches:

2 x Harken 1000.3 ST three speed, electric drive, self-tailing primary
winches;
2 x Harken 74.2 ST two speed electric drive, self-tailing halyard winches;

4. Rigging and Sails

Standing Rigging:

The vessel is fitted with discontinuous Maxspar rod rigging for the 3- spreader rig. The standing rigging includes a split backstay which is made of high performance steel and Dynema for the backstay legs, with plates below deck;
Discontinuous rod rigging for tip-cups;
Enclosed rod rigging for tip-cups;
Stainless steel rod, which incorporates high strength, low stretch and high corrosion resistance;
Stemball spreader links and stemball tang fittings used throughout;
Total weight of standing rigging is: 340kg;

Running Rigging:

1 x 16mm dyneema main halyard;
2 x 16/14mm dyneema/dynaone headsail/blade halyard;
1 x 14mm dyneema storm/jib halyard;
1 x 16mm dyneema boom topping lift;

2 x 16mm dyneema asymmetric halyard;
1 x 16mm dyneema mainsheet;
2 x 16mm dyneema blade jib sheets;
2 x 14mm dyneema storm jib sheets;
2 x 16mm dyneema reef lines;
2 x 18mm dyneema checkstay runner tails;

Backstay and Vang Hydraulics:

1 x Cariboni hydraulic backstay tensioners with mechanical lock-off;
1 x Cariboni hydraulic vang with carbon cover;
Operation of these rig hydraulics is powered via a push button console fitted
on pedestal and with a manual backup control unit close to port pedestal;

Blocks:

Spinlock;
2 x stand up single block on bulwark;
2 x pad eyes;

Mainsheet System:

The system is managed by a magic trim system which is installed below deck at mast level. This allows to have a double point mainsheet on the rollbar and therefore the cockpit and deck remain as clear as possible;

Headsail System:

The system uses an auto/tacking jib with single track and single car;

The car can be also used for the removable staysail;

There is a single jib sheet, going from the traveller up to the mast and then down concealed under the coachroof and back to one of the aft winches;

Headsail System:

Bamar electric headsail furling which gives push-button reefing and furling
of the jib;
Unit finished in black anodizing and stainless steel and concealed below
deck to create a flushed bow area;
Manual backup;
Dual controls are provided for each headsail furling function, so the sail may be furled from either side of the cockpit;

Storm Staysail System:

Removable storm jib stay;
Storm jib halyard;
Cariboni hydraulic tensioner;

Rigging Hardware:

Fittings, tip-cups, etc., for discontinuous rod rigging;
Deck ring fabricated in spartite (composite) x 2 kits;
Conduit for masthead instrument wiring;
Spinlock ZS rope jammers for storm jib and blade jib halyards;
Spinlock ZS rope jammers for mainsail halyard and topping lift;
Mast jacking system;
SAILS (by North Sails) Mainsail – SRP 105 – 5 x full-length carbon battens, loose foot, two rows
of reefing points each with custom leech reef block;
Mainsail boom cover in acrylic;
Furling and Selftacking Jib – SRP 105, including a foam luff pad and UV
stripes;
All sails feature a custom graphic design;

5. Electronic Systems

Navigation Instruments:

2 x Raymarine i70, supported data views include: Wind, Speed, Depth,
Tri-data and navigation integrated with the Chart Plotter. The instruments
are installed on each pedestal;
Raymarine SPX-30 SmartPilot autopilot with T3 hydraulic linear drive unit;
2 x Raymarine p70 autopilot remote control located at pedestal and chart
table;
2 x Raymarine e125 Chart Plotter at both pedestals with integrated Digital
Radar and built-in 50 Channel Global Positioning System (GPS), interfaced
with the autopilot;
Raymarine 4kW Radome radar antenna mounted on mast;
Raymarine Ray 240E, Class D-DSC VHF radio-telephone with antenna at
masthead and second station at pedestal;
Magnetic compass;

Entertainment:

Stereo FM Radio/CD Player with iPod and iPhone connectivity. One is fitted with four loudspeakers in the cockpit and has a remote control with twin loudspeakers to the foredeck. Inside the yacht every cabin has a separate stereo system while the master suite and main saloon feature a proper home theatre system which includes stereo and iPod connection.
The stereo system can be also controlled via wifi by an iPad;
8 x OX-Home mirror TV’s are fitted throughout the yacht including bathrooms;

6. Engine Room Equipment

General:

The engine room surfaces are faced with white painted sound absorbing aluminium panels. The engine room access is below the ladder which connects the main saloon to the forward cabin, all other access panels are extra ordinary service panels into the salon floor. The engine room has 24v lighting and is fitted with extractor fans ducted to the exterior through concealed into coachroof grids. An automatic fire extinguisher is fitted with remote indicator light;

Propulsion:

2 x Yanmar Common Rail 4BY2-150 diesel engines, 150hp @ 4,000rpm
ZF reduction gear, which gives a reduction of 2.45:1;
2 x 22” 3 fixed pitch and blades propellers;
2 x 40mm stainless steel shafts lines;
2 x Bronze P-bracket and a PSS water-lubricated lip seal stern gland system;
1 x 15kW SP240 TCi Side Power electric bowthruster with speed control PPC 800;

7. Electrical System

12/24 Volt:

Domestic bank batteries are 24V AGM type, deep cycle series, with a total capacity of 2000 Ah @ 20Ah rate. This battery bank also serves the bowthruster load;
Engine starting batteries are 12V AGM type, heavy duty type (one battery for each engine);
Generator starting battery 12V AGM type, heavy duty type;
2 x 24V/100 Ah alternators (one for each engine);
24V/12V converter, used to charge the engine batteries bank through the alternators;
100A/24V Skylla-TG battery charger;
24V/5000W Phoenix inverter;
12V/30A Phoenix Charger for engines and generator;
24V/12V Blue Power IP20 battery charger for emergency battery bank;
Circuit breaker system;
Victron Easy Control Panel acting as a voltmeter and ammeter for monitoring the vessel’s batteries status;
Batteries isolators;

220 Volt:

1 x 20kW (50Hz) Kohler 4-cylinder diesel generator running @ 1,500rpm installed within manufacturer’s sound shield, located into the fully – insulated engine room. An exhaust water separator and waterlock are installed.

The unit has a remote Start/Stop and instruments mounted on the AC electrical panel at chart table.
220V AC circuit with outlet sockets located as appropriate within the layout;
1 x 63Amp dockside power cable, 3-core double insulated PVC; socket
located on the aft deck;
1 x 100A/24V Victron Battery Chargers;

9. Bilge System

General:

8 x Rule electric bilge pumps;
High level bilge alarm with double level sensor;
Manual bilge pump operated from the side of the cockpit and fitted with a metal deck plate;
Emergency electric bilge pump by Gianneschi, with manual clutch, rated to pump approx. 125lt/min;

10. Fuel System

General:

2 x aluminium tanks providing a total capacity of 1,900 litres, including the
return tank;
Tank inspection cover, one for each;
Tank deck fillers;
Tank gauge system;
Duplex Racor fuel filter and water separator unit is installed with warning lights at the electrical panel. With this system each filter can be isolated whilst maintaining the all machinery up and running, allowing in-use filter replacement and cleaning;

11. Water System

Fresh Water System:

2 x structural tanks totalling 1,360 litres. The GRP tanks are treated with inert gelcoat, fitted with baffles and provided with multiple inspection covers;
1 x 80lt Quick B3 80 water heater; the water is heated by the engine’s heat exchanger or by a thermostatically-controlled 220V, 1.2kW immersion heater element;
180lt/h Idromar MSK 18 watermaker;
Tank deck fillers;
Tank gauge system;

Grey Water:

3 x Sanisplit pressure lines which serve two grey-water aluminium tanks (totalling 220lt) located in the engine room, fitted with a float switch and a Gulper pump, giving automatic evacuation of all showers, washbasins and galley sinks;

Black Water:

5 x Tecma macerator toilets;
1 x 110lt aluminium black water holding tank;
Tank gauge system;
The tank is configured for discharge below water with additional ability to be pumped out from deck via flush-mounted deck fittings.

12. Other Options

General:

60,000 BTU Condaria reverse cycle 220V air conditioning, 8 units;
Barazza Microwave;
Miele electric oven;
Miele Dishwasher;
Miele Washing machine;
Bora 4-plates electric hob;
Bora extractor fan;
Waeco Coolmatic HDC 150 liter 24V fridge, front opening, fitted into the
galley;
Waeco Coolmatic CB 40 Liter 24V fridge, top opening, fitted into the galley;
Third fridge, top opening, fitted into the cockpit, below the seats;
2 x LED underwater lights;
Lopolight tri-wihite light at masthead;
Windex type Wind indicator at masthead with dedicated light;

2 x boom lights over cockpit;
Pair of down and up spreader courtesy lights;
Master gaiter cover in waterproof fabric;

13. Accomodation

General:

The layout allows for a maximum of eight guest berths and two crew, in five cabins, with five heads and separate shower compartments. Owners', guests' and skipper's cabins will have hanging lockers with auto light. All cabins have a mirror fitted.

Deck Saloon:

Access to the Saloon from the cockpit is via a set of teak covered steps, backlighted on the bottom side, with stainless steel handrails on side. The ladder structure is made of aluminium. A custom double sliding, smoked glazed access system is installed at the companionway. This system has a mechanically balanced and assisted operation. The access ladder continues aft, in order to give access to the guest area, and features a Plexiglas divider between the steps going outside and the ones which give access
to the guest area. Below the ladder, in the foyer, a little settee or alternatively a little storage or oilskin locker find place, while below the steps going down into the foyer, which can be removed, there is an access to the main electric switch panel.
Going into the saloon there is a large table to starboard which serves an ‘L’ shape large settee, leather upholstered. The table has a veneered top panel with stainless steel details and it features a sliding mechanism.
There may be also additional stools in order to create more sitting area.
Alternative custom tables are available on request.
To the aft side of the sitting areas, on the bulkhead, a good size mirror TV finds place. A custom drinks locker is fitted forward, surrounding the mast area.
To port side there is a bar area which also works as a kitchen island and which can be provided with tall stools. The island is covered with ‘slatelite onice classico’ on the saloon side which is also backlighted. On the port side, the galley and the chart table find place.
The material used within the saloon are ‘Eucalypt fumé’ for the joinery, white leather and stainless steel strips for the floors and white leather and sand nabuk leather for the headlining. The hull sides, hullports and hatches recesses are upholstered with brown leather, while the venetian blinds are made of wood and leather. The sofa is white leather upholstered.

The Deck Saloon is extremely light and airy, with four bonded to coachroof windows and two opening deck hatches. There are also two long nonopening hullports, one per each side. These hullports contribute to the great feeling of light and space, giving a panoramic view whilst at anchor.

Galley:

The galley has a single, long surface taking the most of the length of the deck saloon. The worktop is covered with ‘Callisto slatelite’ stone with all the appliances being flushed to worktop. The same slatelite material is also used on the floor.
The appliances include a double electric hob for a total of four hot plates by Bora which also feature a particular extractor fan in the middle, again by Bora, fitted on the worktop and assuring a good smoke and odour extraction with the minimum noise. Beside the hob is a sub-counter top mounted ceramic and custom made single sink, which is served by a retractile tap by Barazza. The galley also features an electric oven by Miele
and a microwave by Barazza, together with a front-opening fridge and a top-opening one, better described in the refrigeration chapter. The galley also has a front-opening slim line dishwasher by Miele, for up to nine covers.
Both the refrigerator and freezer have an automatic door light fitted and are provided with their own compressors.

Nav Station:

On this yacht the chart table area is located in order to be a natural continuation of the galley worktop, forward of the galley, and it’s provided with two front-facing panels which accommodate the all electronics, a substantial chart table and a stool which can be removed when not in use.
A small stainless steel support stay is fitted on the chart table lid. There is provision for the stowage of charts. Stowage will be provided also for navigational books, almanacs, etc.

Master Cabin:

The aft cabin is configured with a double berth which is centerlined, one pouf which serves a dressing table and an office desk, plus two large hanging lockers, with drawer and locker space. There is access to the ensuite aft bathroom which is split in two parts, located forward to both sides, one for the shower and the other one for wc, both served by a washbasin.
This cabin is also provided with a safe, flush fitted with digital keypad.

Master Head:

This bathroom is split in two separate areas, on port and starboard side.
The starboard side one includes a separate shower by Bianchi e Fontana and a washbasin; the shower walls and floor as well as the bathroom floor, walls and washbasin counter top are all covered with San Laurant marble with part of the shower corners to be backlighted. Also the washbasin is hollow into the same material and has taps by Fantini and plumbing by Paffoni.
The port side bathroom features a washbasin and a Tecma electric wc (black colour) and the same material as per the starboard one but has Alpilignum joinery instead of marble which is fitted on the floor and on washbasin counter top and stowage doors only. This bathroom also has a mirror TV’ which is hidden behind the mirror.
Headlining for both bathrooms are made of white LED backlighted panels.
Quality large type mixer taps, thermostatic shower controls and fittings are by Fantini and Inda.
Lockers for wash bags, cleaning materials and linen stowage are provided.

Guest Cabins (STB and PRT):

Forward of the master cabin are a pair of guest double cabins, one either side of the corridor.
One of those cabins is configured to be an upper/lower berthed cabin, while the other is a double berth one. Each has en-suite WCs and showers and a hanging locker. The beds also feature a big storage space under the slats net which can be lifted up.

Guest Head:

The two aft guest’s bathrooms serve the two aft cabins and are almost specular. They are both fitted with a separate shower by Bianchi e Fontana and they feature walls, floors and washbasin counter top in “Slatelite Selene”. The headlining is made of “Dani Boxland” leather and of varnished panels. The wc’s are Tecma electric (colour black). Both the bathrooms feature quality mixer taps and thermostatic shower control by Fantini
and fittings by Inda. In particular the taps are fizzed to floor and have a cylinder design.
The washbasins are mounted on the slatelite counter top and are by “Glassdesign” (colour black); the port side one is a gum type (flexible).
In both bathroom there are rollaway stainless steel wirings fitted in the shower which can be used to hang wet clothes; in this way the shower cubicle can be used as an oilskin locker.

VIP Cabin:

Forward from the saloon, which also include the galley on the port side, there is a VIP double berth cabin which uses the all beam of the yacht and has an en-suite good size bathroom on the starboard side. This cabin is also provided with a safe, flush fitted with digital keypad.

VIP Head:

The VIP bathroom takes the all length of the VIP cabin and is placed on starboard side. The shower walls and washbasin top are made of “Slatelite Elios”, while the other walls feature an “Alpilignum” joinery. The floors are made of “Calacatta Oro” marble which is also backlighted into the shower.
The headlining are made of “Dani Boxland” leather. Hidden behind the mirror, a TV finds place too.
The wc is an electric Tecma (Black colour) and the quality mixer taps and thermostatic shower control are by Fantini, while the bathroom’s fitting are by Inda. The washbasin is a ceramic type, squared, over counter top mounted, by “GSG Ceramica” (glossy white colour).

Crew Cabin:

Forward of this cabin is a double crew cabin with en-suite head and integral shower. This cabin is also fitted with a laundry corner which includes a washer-dryer; the access to this cabin is through a generous size deck hatch only.

Crew Head:

The Crew head which is accessible from the crew cabin only, features a Corian type floor with integrated grate for shower drain. The bathroom has an integrated shower and for this reason all the wall, lockers and other surfaces are made of easy to clean material. The bathroom has taps and shower fittings by Paffoni and a Tecma electric toilet (white colour).
In the bathroom as well as in the cabin itself there are rollaway stainless steel wirings fitted which can be used to hang wet clothes; in this way the bathroom can be used as an oilskin locker, while the cabin area can be used as a drying area.

Disclaimer

This offering is subject, but not limited to, errors, omissions, price fluctuation, and prior
sale or withdrawal without notice. All details disclosed are without guarantee and solely
based on the information received by the seller, intended as a general guide to the Yacht.
Engel & Völkers cannot be held liable for any lack of completeness, inaccuracy, or ambiguities
and/or errors contained in the information disclosed. It is the buyer’s responsibility
to disclose the details of any concern(s) to the seller, by the request of a survey, inspection and/or enquiry. The buyer must ensure that the purchase contract properly reflects his
concern(s) and that it sets out any representations and/or details on upon which he may
rely. Engel & Völkers always advises the buyer to conduct an independent survey
prior to the purchase. We are at your disposal for any further information about the
Yacht. Upon receipt of notice, the Yacht is available for viewing at any time, accompanied
by our Yacht Broker. The Seller is responsible for the payment of Commission

2016 Travel Lite 625 Super Lite Review

Read article : 2016 Travel Lite 625 Super Lite Review 

370 Shares

TCM reviews the half-ton targeted 2016 Travel Lite 625, a short or long bed hard side, non-slide, non-bath truck camper.  Can a camper small enough to fit inside a short bed tailgate actually be worth owning? According to Dustin Johns, President of Travel Lite, the reasons for building the 2016 Travel Lite 625 called him on the phone constantly.  When the625 debuted in Truck Camper Magazine in June of 2015, Dustin explained, “Our customers and dealers have wanted a half-ton short bed camper that would allow the tailgate to be kept up, offer plenty of interior room, and feature basic amenities including a stove, sink, and refrigerator.  I was asked to build this camper many, many times.”

Above: The Travel Lite 625 at D&H RV Center in Apex, North Carolina

From the repeated requests, the Travel Lite team designed a hard side truck camper that would fit inside of a 6.5-foot short bed truck with the tailgate closed.  Keeping the camper inside the tailgate would allow for towing without an extension hitch and provide the best possible turning radius for the rig.  Once lowered, the tailgate could then become a small deck for sitting or gear.

Perhaps the Travel Lite 625’s most impressive trick is its ability to work with short and long bed half-ton trucks.  It looks a bit odd mounted on a long bed, but the two feet of bonus truck bed storage is perfect for toys, gear, and water containers.

To keep the weight down, Travel Lite used the materials, construction approach, and design concepts of their best-selling 770 Super Lite model.  The 625 features the same overall profile, kiln-dried Banak wood from South America, and cabinetry netting as the 770.  Further eliminating weight, the 625 was designed without a bathroom, black tank, or grey tank.

Dustin reported the initial dry weight of the 625 at 1,285 pounds and gave the camper a $10,495 MSRP with standard build options; refrigerator, sink, stove, fresh water tank, converter, and manual Rieco-Titan jacks.  Clearly Dustin was looking to put a sizable dent in the half-ton truck camper marketplace.

Of course the path to half-ton truck camper paradise is paved with good intention truck camper designs that never caught on.  These campers were usually too heavy, too expensive, or too small to become a consistent seller in the marketplace.

The question is, will the Travel Lite 625 break through where so many others have failed, or end up in the half-ton truck camper bin of history?  It’s time to put the 625 under the microscope.

We photographed the 2016 Travel Lite 625 seen in this review at D&H RV Center in Apex, North Carolina.

Floor Plan Evaluation

As seems to be the trend of late, the Travel Lite 625 is infused with the ideas and lessons of the past five decades of truck camper design.  This is not a fancy SolidWorks modeled multi-slide with intricate cuts and exotic amenities.  You’ll find no CNC-routed curves or luxury appliances here.

What you will find is an firmly old-school, pencil-to-paper, saw-to-wood truck camper design that shoe-horns an impressive amount comfort and utility into a short bed half-ton compatible truck camper.  Shut the tailgate and that’s exactly what Travel Lite’s dealers and customers asked for.  As the saying goes, give them what they want.

Above: The large 4-foot sliding dinette window brings in a ton of light

Stepping into the 625, the careful design decisions are everywhere.  The main living space feels open and spacious with plenty of light from a dual-window entry door, two large windows in the dinette, and a cabover side window.  Kitchen and dinette cabinetry and storage are readily available and the overall level of materials feels solid and durable.

While we didn’t take precise measurements, it appears that half of the available kitchen counter top is taken up by the single-basin sink and two-burner cooktop.

The flip-up counter helps by adding about 25-percent more counter space, but it’s still a tight set-up for preparing anything other than the basics.

To put this into perspective, Angela and I are connoisseurs of culinary basics on the road.  Our coffee, tea, one-pot-meals, and endless PB&J sandwich preparations would all work fine between this kitchen set-up and dinette table.  Now our laptop-to-laptop work requirements would be seriously challenged, but that’s another topic.

The U-shape dinette in the 625 was designed to accommodate three to four adults (if they’re very good friends) around the table for meals, conversation, and cards.  In reality, the dinette seating, table, and available leg area is best for two adults.  With just two, there’s plenty of floor space for legs and feet underneath, and ample table room for two plates of food, and drinks.

If this were our camper, we would want a larger table, and a more stable table leg and/or wall attachment system.  There’s nothing worse at a restaurant than a table that moves when you put your dinner plate or elbow on it.  With a single post, this table is fairly stable, but requires care not to bump it.  Naturally, one table leg is less weight than two, and a smaller table weighs less than a bigger one.  Compromises, compromises.

Above: The table and table leg are easy to remove for more room, or to make the dinette into a bed

Above: The porta-potti has a convenient storage compartment under the dinette

The dinette quickly makes into a 6-foot bed with the provided cushions.  This makes the 625 an ideal choice for the hunter or fisherman who wants to bring a friend for a weekend trip to that remote hunting ground or fish camp.

Above: The dinette makes into a 6-foot long bed

On the rear wall, the 625 features a 110-volt outlet and the thermostat.  While I don’t foresee this unit connected to shore power often, this outlet will be vital for charging computers, phones, and cameras while hooked up to AC or a portable generator.

Above: Standard on the 625 is a two-cubic foot refrigerator, which can be upgraded to the three-cubic foot size shown

The three-cubic foot, three-way refrigerator is ample for a camper this size.  In the past, campers targeting the short bed half-ton size and weight came primarily with ice boxes if they had cold-food provisions at all.  Having an actual three-cubic foot, three-way refrigerator is quite a luxury in this weight category and price.

Just below the refrigerator is a cabinet dedicated to a sealed enclosure for the 625’s single battery.  When I opened this cabinet, I was hoping to see storage, and found myself disappointed that this space was almost completely used.

I would look into moving this battery elsewhere.  My favorite go-to battery moving product is the Torklift International Hidden Power that places a battery inside a protected and sealed box under your truck.  With this modification, you could recapture this valuable storage space without losing the house battery.

Another option is changing to sealed AGM battery in this location.  You won’t gain your storage back, but you’ll likely gain more amp hours.  Then again, a bigger battery adds cost and weight.  When designing a camper for a half-ton short bed, trade-offs abound.

To the right of the refrigerator and battery cabinet is a large two-section cabinet and pull-out drawer.  With its immediate proximity to the kitchen and dinette, the drawer will likely be used for silverware, cooking utensils, and other kitchen items.

The large two-section cabinet is open season.  Some will use it for dry food, pots, and pans, while others will store clothing and camping gear.  We would at least attempt to use the cabinet over the sink for all dry food, cups, and plates, and use this space for a limited number of pots and pans, and then clothing and camping gear.  In truck camping, less is more.  In truck camping in a small camper, even less is even more.

Below the pull-out drawer is where you’ll find the stereo system, power converter, and fuse panel.  Having the stereo system and fuse panel easy to reach mid-ship makes sense.

The opening into the cabover is wide open and inviting with white-color LED lights perfectly placed for general lighting and reading.

Above: The cabover ceiling has a 110-volt outlet and provisions to add a 12-volt television

On the other hand, there’s not a single cabinet for clothing in the cabover.  Not one.  There is however a main LED area light, two smaller reading lights, a 110-volt outlet, and provisions to add a 12-volt television.  No cabover muss.  No cabover fuss.  That’s it.

 
Above: The overcab bed on the passenger’s side (left photo) the driver’s side (right photo)

In practice, I expect most folks will bring duffel bags for their clothing and keep the bags in the cabover when they’re not sleeping.  Duffel bags (or whatever cloth based luggage you prefer) are light weight and highly portable, especially compared to standard wood cabinetry.  Unless you just have to have your clothing folded up and put away, duffel bags make a lot of sense in a small camper like the 625.

Specifications

Specifications
Dry Weight	1,285 pounds
Wet Weight*	1,755 pounds
Floor Length	6’2″
Overall Length	10’10”
Width	78″
Interior Height	6’6″
Exterior Height	7’0″
Center of Gravity	29″
Truck Type	Long or Short Bed

At 1,285 pounds dry, the Travel Lite 625 is not the lightest weight hard side truck camper on the market, but it’s in the ballpark.

Travel Lite offers a range of options for the 625 including a solar panel system, electric remote-controlled Rieco-Titan jacks, roof rack, ladder, and an awning.

Above: Rieco-Titan manual jacks, cable television connection, shower power connection, and 110-volt outlet

Unfortunately, you could quickly defeat the concept of the light weight 625 if you add a lot of options.  Just the above mentioned list could add 150 pounds, or more.  In a camper where the design team opted for cabinet netting instead of cabinet doors, that doesn’t make a lot of sense.

Above: The Travel Lite 625 is 78-inches wide and 7-feet, 4-inches tall on the exterior

The 78-inch width of the Travel Lite 625 is 14-inches narrower than Travel Lite’s mid-size truck campers and 17-inches narrower than their largest models.  Obviously, every additional inch in length, width, and height on a truck camper adds weight.  For a camper targeting short-bed half-ton trucks, the 78-inch width strikes a good balance between interior space, and weight.

Above: The ceiling in the 625 is full height at 6.5 feet

One aspect of the 625 design that’s full-size is the interior height.  At 6.5 feet, standing in the Travel Lite is like standing in a much larger truck camper.  There’s plenty of headroom, even for tall folks like me.  That headroom helps give the 625 its roomy feel.

Above: The Travel Lite 625 on a long bed truck, photo courtesy of Travel Lite Campers

Perhaps the most controversial aspect of the 625 is its long bed compatibility.  Mounted on a long bed truck, the 625 looks fairly ridiculous as it locates the unit two-feet inside of the truck bed.  To say this is an unusual rig aesthetic would be an understatement.  For many – us included – the immediate reaction was, “What the heck is Travel Lite thinking?”

long bed truck" width="800" height="539" />

Above: The Travel Lite 625 on a long bed truck, photo courtesy of Travel Lite Campers

Well, Travel Lite was thinking that the 625 is compatible with the widest possible number of truck bed lengths and payload capacities.  In short (no pun intended) the 625 is compatible with many half-ton trucks, all three-quarter and one-ton trucks, and works equally well with short bed or long beds.  Does it look funny on a long bed?  Absolutely!  But very few hard side truck campers have this kind of truck compatibility.

short bed tailgate closed" width="800" height="556" />

Above: The 625 on a short bed truck with the tail gate closed, photo courtesy of Travel Lite Campers

And we must recognize the point that mounting the 625 on a long bed allows for the remaining two-feet of bed space to be available for whatever the owner wants it for; bikes, water, gear, you name it.

Capacities

Capacities
Fresh	9 gallons
Grey	N/A
Black	N/A
Water Heater	6 gallons
Propane Tanks	20 pounds
Batteries	Optional

With nine gallons of fresh water, no grey tank, no black tank, and no inside bathroom, there’s not much to talk on the subject of the 625’s holding tanks.  Since you’ll likely only be using the fresh tank to wash hands, wash dishes, and brush teeth, the nine gallons could last upwards of a week, or more.

If you plan to scare the bears and use the outside shower, the nine gallons may only last you a couple days.

city water connection" width="800" height="534" />

Speaking of bears, I can hardly believe Travel Lite included a city water connection for the 650, but they did.  Without an inside shower, I can barely find a reason for this.  Maybe so those who enjoy flashing the wildlife take extended outside showers?  Hide your eyes Mother Nature.  Nothing to see here.

The single vertical 20-pound propane tank is absolutely perfect for the 625.  Not only are vertical tanks exchangeable at nearly every Walmart, Lowes, Home Depot, and gas station from coast-to-coast, but a 20-pound capacity should last a long time in a camper this size, unless you’re camping in the seriously cold.

When camping with a single tank you always need to keep tabs on your usage.  When that tank runs out, there’s no second tank to change to.  If we had one tank, I would fill it long before empty, just like putting fuel in the truck.

Travel Lite lists the battery as optional on the 625.  You could connect the 625 to your truck’s battery and gain the space we talked about earlier, but that would not be our recommendation.  All it takes is one night of running the furnace in cold weather and you could be stranded with a dead truck battery.  Whether you get the built-in battery Travel Lite provides, or another battery storage solution, we definitely recommend a house camper battery.

Wet Weight Calculation

Using the standardized Truck Camper Magazine wet weight calculation, let’s run the numbers on the Travel Lite 625.

Base Dry Weight, plus single battery option

Travel Lite 625: dry weight, 1,285 pounds + 9 gallons fresh, 75.1 pounds + one battery, 65 pounds + 20-pound full propane tank, 20 pounds + stuff, 500 pounds = 1,945.1 pounds

Since we don’t foresee or recommend many options being added to the 625, we’re not going to run an optioned wet weight calculation.  As it is, the final wet weight of 1,945.1 pounds may shock some folks.

500 pounds of that weight is the standardized “stuff weight” that we add to each and every wet weight calculation in Truck Camper Magazine.  In a small camper with limited storage like the 625, 500 pounds of stuff weight is likely more than required.  If we subtract half of this stuff weight, we get a more realistic 1,695.1 pounds.

Truck Recommendations

To remain conservative, we are going to match the 625 with a 1,695.1 pound wet weight (250 pounds of stuff).  This may still be high, but we always play it safe when it comes to truck and camper matching.

For those who haven’t looked at too many payload stickers, it may come as a surprise to learn that many half-ton trucks don’t have 1,695.1 pounds of payload.  Many older half-ton trucks, or trucks with fancy packages and long option lists, have considerably less.  Do not assume that any half-ton truck has this kind of payload.  It might, but it might not.

That said, it would be a cinch to either locate or order a half-ton truck with 1,695.1 pounds of payload, or better.  If you approached your preferred local dealer and said, “I need no less than 1,700 pounds of payload in a half-ton truck” they should be able to work out the specifications you require, and locate or order the right truck without trouble.

You could also take those same specifications and find a used half-ton with enough payload.  New or used, always check the actual payload sticker (the yellow sticker inside the driver’s side door) on the actual truck before making a purchase.

If you are purchasing a new or new-to-you truck, it’s also worth considering buying even more truck.  Two years from now you may want a bigger camper.  Why not buy the right truck for that bigger camper now?  In trucks, you often don’t pay that much more to get a lot more payload.

The Verdict

Some truck campers are designed to wow the senses.  You walk in and they have a dance floor of interior space, a dinette ready for six, a refrigerator that could swallow a beer keg, and storage that could empty your attic.  You know you’re in one of these campers when the HDTV is almost as big as the one you have at home, and there’s a fireplace underneath it (almost kidding).

Where these campers “wow the senses”, the Travel Lite 625 “wows with common sense”.  From the very concept of the unit, to the way the camper was designed and built, everything about the 625 is a carefully considered compromise to create a hard-side unit that’s truly half-ton compatible.

Judged from this perspective, the 2016 Travel Lite 625 is a roaring success.  Yes, it’s chock full of compromises compared to the “wow the senses” models, but these compromises were the right ones to make the half-ton targeted size and weight.  The form, function, and comfort this camper offers half-ton truck owners – especially for the price – is very impressive.

In short, Travel Lite has built a truly half-ton compatible truck camper that’s worth owning.  Yes, you will still have to run the numbers to make sure the 625 will match your half-ton truck, but the chances are very high that it will.

If you’re in the half-ton truck camper market, and can live with the 625 list of compromises (tight kitchen, no bathroom, no grey tank, no cabover storage, etc.), this camper deserves to be on your list.  With the 625, Travel Lite has a serious half-ton ready contender.

Pros
Low weight and forward COG maximizes half-ton potential
Short and long bed truck ready
Tailgate closes on a 6.5-foot short bed truck
Excellent sense of interior space for a small camper
Good amount of kitchen and dinette area storage
Dinette makes into a 6-foot bed

Cons
Very tight kitchen area
Very limited 9-gallon fresh tank, no grey, no black
No bathroom, but features a porta-potti cabinet
Extremely tight kitchen counter space, but extension helps
Optional single battery takes up valuable interior storage
No storage in the cabover – pack your duffels

Model Information
2016 Travel Lite 625
MSRP: $10,495
Warranty: 1 year from time of purchase

Travel Lite, Inc.
71913 Country Road 23
New Paris, IN 46553

Phone: 574-831-3000
Request A Travel Lite 625 Brochure
Web: TravelLiteCampers.com

Quality, Customer Service, and Long-Term Reliability

Truck Camper Magazine inspects all reviewed truck campers for design, material, and quality issues and reports what we find.  However, since Truck Camper Magazine reviews only brand new truck campers, our reviews do not address long-term quality, customer service, or reliability.

To learn about a brand’s long-term quality, customer service, and reliability, Truck Camper Magazine recommends talking directly with truck camper owners at truck camper rallies and online via truck camper forums and truck camper owners groups.

Please be sure to balance your gathered feedback across multiple sources including direct correspondence with the truck camper manufacturers and your closest truck camper dealers.

If you are new to truck campers, start here.

Recommended for you

Dream Camper Floor Plan Contest

Read article : Dream Camper Floor Plan Contest

Dream Camper Floor Plan Contest – Part 2 http://www.truckcampermagazine.com/news/dream-camper-floor-plan-contest-part-2/"> Dream Camper Floor Plan Contest – Part 2&BODY=I found this article interesting and thought of sharing it with you. Check it out: http://www.truckcampermagazine.com/news/dream-camper-floor-plan-contest-part-2/"> 12 more reader submitted dream floor plans including raw concepts, wild ideas, and subtle refinements.  And the winner of the first ever dream truck camper floor plan contest is… Just last week we visited a prominent truck camper manufacturer and the subject of our dream camper floor plan contest came up.  We talked with great excitement about the variety of ideas our readers were presenting, and encouraged them to study the plans when they debuted.  No, we didn’t give them a sneak peak.  It’s more fun to tease. None of the submitted designs, including mine, are anywhere near production ready.  That was never the intention or spirit of this contest, nor is it possible without delving into details like plumbing, electrical, and code compliance.

The true potential of this contest is to give truck camper users from around the United States, Canada, and the world the opportunity to directly inspire professional truck camper design teams.  You know, the folks responsible for the truck campers you see debut here on Truck Camper Magazine, at RV shows, and dealer lots?  This was your shot to show them your big idea, and possibly change the course of truck camper design history.

I know, crazy talk.  Then again, crazier things have happened.  I’m going to lobby the industry to take your designs and ideas seriously, as I do with our bi-annual truck camper survey coming up this fall.  Together, we will change the course of campers.

Far be it for us to determine who should win the best dream camper floor plan, except that’s exactly what we had to do.  This is, after all, a contest, and we are the big cheese, cheesette, and cheese-cat for this electron-only magazine.  After considerable review, and a tail gesture we interpreted as positive, we have a winner.

The winner of the first ever dream truck camper floor plan contest is…

Karl Pettitt, Elmhurst, Illinois – Winner

Above: Click to enlarge this floor plan and the others below to see them bigger.

Although I don’t currently own a truck camper, I would like to in the future.  I often think of what an ideal floor plan would be so this was a fun exercise.  I first did the layout in a program that was to scale.  The dimensions should be pretty accurate.

The floor length is 11-feet.  The total length is 19-feet, 9-inches.  The width is 8-feet.  It’s a single-slide, dry bath, flatbed model.

Although there are a few flatbed model campers on the market, I think there is a great deal of room for more.  Specifically, I think there is room for a larger model that takes full advantage of the ability to place the door anywhere.

To this end, I created a floor plan layout that places the door towards the front of the curb side of the camper.  This allows for greater flexibility in the placement of the bathroom, which I put across the entire rear of the camper.

The slide allows space for both a dinette and a small couch that can turn into a bed.  Placement of the kitchen towards the front, along with the heaviest components such as the fresh water tank, battery bank, and propane tanks, will help in keeping the center of gravity as close to the front as possible.

The placement of the entertainment center allows for viewing either on the main floor or the cabover.  There is overhead storage above the kitchen and couch that makes up for the lack of floor cabinets.  There is also ample windows allowing light in from either side of the camper as well as views.  I think this would make an ideal camper for a family with the potential to sleep up to six people without the use of a bunk.

#16 – David Miller, Branson, Missouri – Honorable Mention

My camper is designed with the premise that the most important things about a truck camper use are (1) the nice, soft, queen bed for sleeping, and (2) the nice bathroom for showering; not a wet bath.

The dining aspect needs less emphasis because, typically, the meals are simple and small.  In most cases, weather dependent, we eat outside at the picnic table.  Thus there is no need for a large dining table.

There is also no need to accommodate guests for sleeping.  If the grandkids are camping with us, they will sleep in a tent outside.  The concept of having the table convert to a bed is unnecessary, and a waste of space for us.

The attached drawing is for a non-slide design to fit a full-size short bed pickup.  I figure this camper will hang over the back of a 6’6” truck bed by approximately 27-inches.

Here are the wonderful features of my perfect truck camper:

It has a dry bath and shower.  This is extremely important.

The dining area has been reduced in size to only seat two adults.  The table is curved and the back of the seat cushion is curved to give the feeling and seating of a corner booth in a restaurant.  The only slight difficulty is that the person who sits down first will have to slide in and cannot get back out until the other person stands up, but, that is just like a corner booth in a restaurant and won’t be too much of a hassle.

There is a closet on both sides of the bed in addition to the foot lockers.  The television is mounted above the table, on the wall of the dry shower.

As you can see, the bed and the dry shower get the most emphasis, and the dining facilities are minimized.  It’s the perfect camper for two adults who want to shower every day after a good nights sleep.

#17 – Jake Schultz, Washington – Honorable Mention

A Folding Camper for the Ford Ranger

This camper is designed to be less than 780 pounds to work within the payload limit of a Ford Ranger.  It’s also designed to be 64-inches wide, with a maximum travel height of 82-inches.  These dimensions allow the camper to fit into a standard 84-inch garage in the folded configuration.

The camper features a full stand-up heigh interior of 76-inches, as shown.  A sun-dome could be added for an additional three-inches of interior height.

The camper has a double-pivot folding hard wall roof and sides with an open and panoramic cabin.

The camper can be used in one of four configurations:

1. Wide open with magnificent panoramic views to the aft sides and back.

2. Open to the aft sides and back, with screen netting in place.

3. Polycarbonate window panels in place (inboard of netting) for inclement weather.

4. Window panels in place and privacy curtains on the interior.

There would be comfortable seating for two at the dinette with the cushions angled slightly inward to account for the wheel well.

The camper would feature a modified full-size bed available at all times.  There would be a 24-inch cabinet for hanging clothes under the foot of the bed.

To save weight, the roof would be built for structure and snow loads only, not to stand on. The floor would be to stand on only if the camper is on the ground or in the bed of the truck, again to save weight.

There would be no jack stands.  The camper is suspended from the owner’s home garage root trusses to remove and store.

There would be an ice chest under one seat and Porta-Potti under the other.  There would be no refrigeration systems or black water tank.

All systems are in one four-foot module along the right side for minimum weight and system run lengths.  The module contains the propane tank, propane heater, two-burner stove, sink, fresh water tank, grey water tank, battery, converter, inverter, and small item storage.

#18 – Mark Larson, Phoenix, Arizona – Honorable Mention

This is my drawing for one of my dream campers.  Please excuse the poor scale on the toilet, lavatory, and kitchen sink.

I know this would be better as a flatbed model because of the side aisle going to the cabover and the location of the shower.  It could also be an above the bed rail model.  I’m with you wanting a camper with no slide outs.  You had a great design of your own.

#19 – Kari Miller, Branson, Missouri – Honorable Mention

My truck camper is the best design ever.  Here are the great features:

1. There is actually a solid wall between the over cab bedroom and the rest of the camper.  This creates total privacy, similar to a fifth wheel with an isolated separate bedroom.

2. The step to the bedroom is offset so there is not direct line of sight into the private bedroom.

3. There is room at the foot of the queen-size bed to access the closet and a real two-drawer dresser, which is what is needed for storing clothes in a camper.

4. A narrow, but deep and tall closet is behind the refrigerator is accessed from the step.

5. Instead of wasting room on a full table top and a table that converts to an unnecessary bed, this camper has a bar top for dining.  The seating consists of two bar stools which can be clamped down for traveling.  People spend many hours sitting on a bar stool so, obviously, these would be comfortable.  Plus, for most eating situations, people will either sit outside at the picnic table, or go out to eat at a restaurant.  There is a big window over the bar top so it would be pleasant sitting.

6. There is a slide-out pantry between the bar top and the range

7. The bathroom has a dry shower, which is important.

8. This camper should fit in a full-size short-bed pickup.  There are no slides, and it is
hard-sided.

#20 – Mike Cianci, Loveland, Colorado

Here’s my plan.  It’s fairly basic.  I chose a wet bath because it’s easier to clean.  Put it in the forward section near the wardrobe with a privacy curtain so nobody has to see your business.  And it’s easier to keep the bed/bath/dressing area cleaner.

I chose wardrobes with shelves or drawers which is more practical than hanging closets.  Who is bringing their tux and ball gown while truck camping?  There are overhead bins throughout where practical.

There would be LED lights, two batteries on a movable tray, and a small solar setup.  Only simple shades are necessary; no cornice, or valance boxes around the windows.

There would be 12-volt and 110 AC throughout, two Fantastic fans – one in the bedroom and kitchen – and an air conditioner   There would be a full-size skylight/dome in the bath with a side wall exhaust vent.

The sofa could be a jack knife-style, or have storage underneath.  And it would have two pull-out tray tables mounted in or adjacent to the armrest.  Plus it would pivot for easy egress from the sofa while eating or using computer, similar to tray tables on airliners in first class.

The television would be on standard pivot for bedroom and living room viewing, and would recess in a cabinet above the slide out pantry.  The rear exit door would have a platform deck for easy entry/egress.

#21 – Kevin Pinassi, New York, New York

#22 – John Wells, Hollidaysburg, Pennsylvania

My design is a modification of the Chalet Ascent S100F, a limited production model (six total!) that Chalet discontinued to pursue production of their more profitable double and triple-slide models.  We love ours because it is completely usable with the slide in or out.

It has huge floorspace when the slide is out for entertaining friends and for ladies to dress in Civil War hoops (don’t ask).  The front bath allows a full height pleated curtain immediately behind the dinette to be drawn across to create a dressing room with access to bath, bed, and wardrobe.

There are no appliances in the slide, minimizing slide-out weight, and wear and tear on electrical and gas connections while maximizing efficiency of the refrigerator.  While we love our camper, please allow me to debut … drum roll… The Wellspring S110F.

My modifications to Chalet’s original design are as follows:

There would be 10-inches of increased length in the main cabin.  On the slide-out side, this extra wall space at the junction of the overcab and cabin strengthens the exterior at the crucial front corner tie-down.  We have already noticed flexing at this point and have taken steps to greatly reinforce this important structural location.  On the kitchen side, this extra 10-inches allows an increase in much-needed counter space, as well as under and over cabinetry.

I would also add about four to five inches to the side-to-side width of the wet bath.  The wardrobe doors and bathroom door would still function even with the slide in.

Additionally, I’d add half-penguin cabinets to the night stands at either side of the bed in the nose of the overcab.  These units would be open-shelved on the sides, half-depth and about 3/4 height, with a small rail or lip on the shelves and top edge to keep books, phones, clock, etc from falling out during travel.

I’d also add a three drawer cabinet with open top shelf and top rail at the foot of the bed on the bathroom side.  I’ve avoided the side hampers as I feel they add significantly to the difficulty of changing the bedclothes, though they could be added quite easily as an option.

#23 – Bob Dold, Monson, Massachusetts

Attached is my submission for the dream floor plan contest.  It is based off an EarthRoamer layout modified with a fore/aft dinette and an undercover slide-out compressor refrigerator chest.  I chose the slide-out compressor fridge since they are more efficient than a three-way refrigerator, and it allows for additional counter space.

One of my favorite features of the EarthRoamer plan is how the closet and bathroom doors can be opened and secured to provide a changing area outside the wet bath with access to the closet.  The wet bath has a wooded floor grate to provide a cleaner surface for the bath when the shower isn’t being used.

Access to the toilet cassette is through the rear storage door which drops down and can be used as a counter when cooking outside.  Another door above the horizontal door to the left of the spare tire can be used to store chairs and other lighter items out of the weather.

I prefer the side entry design as it allows the entire back wall to be used for storage and it allows access to the camper from the curbside when parked without having to remove bikes/trailers from the back of the camper.

The pantry to the left of the closet would be a bank of drawers with a window air conditioner unit above to provide for cool air without the expense and height of a roof mounted unit.  The dinette would be a little under three feet wide and can convert to a single bed if needed.

Large awning windows on either side provide lots of light and views with storage cabinets above them (not shown).  The overcab queen bed runs north/south to allow for getting out of bed without having to climb over your significant other, and has windows on both sides along with a skylight/Fantastic fan for good ventilation while sleeping.

Another feature I don’t see included on many campers any more is a pass through.  I would like the ability to stealth camp and having the pass through allows one to enter and exit the camper without having to go outside.

#24 – Floyd Schotel, Williams Lake, British Columbia

I’ve been dreaming up my ideal truck camper for a little while now, so you’re design contest is a great opportunity to share my napkin sketches!

For fuel efficiency, handling, and stealthiness, my ideal truck camper would be a low profile pop-up design to fit a 6.5-foot bed, full-size pickup.

The camper body extends past the bumper, dropping down for a low step-in side door.  Inside steps lead to the floor height.  This way the back of the camper is open to mount bikes, fuel, spares etc.  Also, the side door is a natural access to the curb or side picnic area.

Most of the windows are in the soft sides of the pop-up.  That way the camper will be more secure when in the locked down position.  In fact, the camper may look more like a service truck than a camper when in travel mode.

I’d keep the camper as small and tight to the truck as possible.  To keep things simple, I can do without a toilet/black tank, but a collapsable shower would be nice.

This camper is designed for boondocking and overland excursions as well as urban stealth camping.  I love the idea of taking my bed and a hot shower with me in a compact camper for a road trip.  No need to stress about finding a hotel, and a meal can be fixed anywhere, pronto!

#25 – Glenn Yauney, Milwaukie, Oregon

Here is an idea of a dream truck camper floor plan.   We started with the floor plan of a 1140 Arctic Fox.   We added a rear slide-out and side entry.

We would prefer a camper with both a rear and a side slide-out.  When towing a trailer, a rear door entry is awkward, thus we prefer a side entry into the camper rather than a rear entry design.   We added a large closet in the rear slide-out opposite the entry door for boots, outdoor clothes, etc.

Storage space is also at a premium, so I propose one that has both ample wardrobe closets and storage space equipped with larger drawers.  You can’t have too much storage space.

Exterior storage isn’t shown, but basement and exterior storage are also a must.

#26 – TJ and Kelly Kretschmar, Kansas City, Kansas

I am a mechanical engineer and have the ability to convert .pdf’s to CAD.  The Unimog part of the drawing can be found in the technical manual from Mercedes Benz website.  I printed the drawing to .pdf, then converted it to CAD.  I then printed the drawing for the Pangea concept and converted the drawing to CAD.

The reason I choose to draw this concept in CAD was to see if it was physically possible to put a garage bay in an expedition vehicle, and to incorporate my own ideas into the same space that would fit on a Unimog chassis with a single rear axle.

I deleted the interior of the lower living area so I could insert my own concept.  The items that I used from the original GXV drawing are the exterior walls, entry door, cassette toilet, and spare tires.  The loft area and access stairway is also GXV’s design, only with one bed instead of the two indicated in their drawing.

I used the Unimog drawing to make sure the entry door, center of gravity, and departure angle were going to work with the design.

We like the Pangea Lifting roof on a Unimog concept, but wanted it to double as a toy hauler.  We put one bed in the loft area to give the dinette area a sense of a vaulted ceiling.  The unit can be used in the down position for extreme cold weather.  The garage door folds down allowing access to spare tires.  The ATV slide out is similar to a Tommy Lift gate.

The camper would be able to detach with its own hydraulic jacks and allow for the installation of a dump bed.

This, of course, is just a dream.  For now our 1994 Hallmark Ute and 2006 Nissan Titan will have to suffice.

Related Items: